Thiroco T-325 Rubberized Cement Wet and Dry Surface
Description
Thiroco T-325 is a new generation of rubberized plastic cement for dry or wet surface meeting all standards of professionals and contractors. This product is compounded with asphalt modified with elastomeric, mineral fibers and refined solvents. This product’s consistency is designed to facilitate its application using a trowel. It’s a durable rubberized product with excellent adhesion and can withstand to weathers characteristics and temperature variations. It forms a tough, flexible and water resistant coating once dry.
Surface Preparation
All surfaces should be sound, clean, dry and free from oil or grease, dust, dirt, loose paint or other foreign matter prior to application. Excess water should be removed, if possible, before the application of Thiroco T-325.
Application
Apply with a putty knife or trowel to an average thickness of 3mm (1/8in). To seal joints and cracks, press tightly to seal all gaps. To repair a larger crack, apply the Thiroco T-325 to cover the damaged surface then place a reinforcement membrane and then apply another coat of Thiroco T-325 over the entire patch. For easier application, store in a temperate place.
Use
It is mainly used to fill cracks, holes and repair deteriorated areas on foundations, asphalt roofs, shingle, vents and chimney joints. The Thiroco T-325 can be used on dry and wet surfaces.
Cleanning
Tools must be cleaned with mineral spirits.
Norm
CAN/O.N.G.C. 37.5M-89
Package
Available in 13.6 kg and 20kg.
Shelf Life
This product can be conserved in its original container, tightly sealed, up to 12 months after purchasing date by the applicator.
Technical Data Table
Specifications
ColorBlack
Solide93 - 97 %
Application to trowel or putty knifeApply coat of 3 mm (1/8") let dry before covering.
Application temperature-40°C to 80°C. The container can be stored in a temperate area for an easier application.
Coverage
7.2 m² (77.2 ft²) for a 13.6 kg
10.5 m² (113.5 ft²) for a 20 kg
The coverage rate is dependent of the surface porosity and temperature.
Density1,19 kg/L or 9,93 lbs/gal.
Touch dry±4 hours
Completely dry*±48 hours
Storage condition
Product must be conserved in a cool and well-ventilated place up 40°C. The product can withstand freezing.
* Drying Time depend of surface porosity and temperature.
Note
Close container after each uses. Keep out of reach of children. If product is applied near a ventilation or air conditioner unit, take necessary precautions to avoid infiltration of solvent odor inside. Keep any open container or freshly applied product away from open flames, sparks or others heat sources. For exterior uses only.
Warranty
10 years limited warranty when installed and / or applied as recommended by the manufacturer. We will replace the product with a manufacturing defect. Under any circumstances the manufacturer will be liable for any amount in excess of the purchase price of the product used. The consumer must ensure that this product is suitable for the intended use. Because of atmospheric conditions, applicator competence and surface conditions being independent of the manufacturer’s control, we limit our liability for one year following the date of purchase, with proof of purchase, to replacement of defective material only in its original hermetic container. Port paid factory (FAB factory).
DANGER
Flammable liquid and vapour. May be fatal if swallowed and enters airways. May cause cancer. Causes damage to organs through prolonged or repeated exposure.
Precautionary:
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not breathe dust/fumes/gas/mist/vapours/spray. Wash exposed and/or contaminated area thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective gloves/protective clothing/eye protection/face protection.
IF SWALLOWED: Do NOT induce vomiting. Immediately call a POISON CENTER or a doctor If exposed: Call a POISON CENTER or doctor/physician. Get medical advice/attention if you feel unwell. In case of fire: Use water fog, foam, dry chemical or carbon dioxide. Do not use straight of water. Store in a well ventilated place. Keep cool. Store locked up. Dispose of contents / container by a local waste disposal company according to regional regulations.
Thiroco T-125 Flashing Cement Wet and Dry Surface
Description
Thiroco T-125 is a new generation of plastic cement for dry and wet surface meeting all standards of professionals and contractors. This product is compounded with asphalt, mineral fibers and refined solvents. This product’s consistency is designed to facilitate its application using a trowel. It’s a durable product with excellent adhesion and can withstand to weathers characteristics and temperature variations. It forms a tough, flexible and water resistant coating once dry.
Surface Preparation
All surfaces should be sound, clean, dry and free from oil or grease, dust, dirt, loose paint or other foreign matter prior to application.
Application
Apply with a putty knife or trowel to an average thickness of 3mm (1/8in). To seal joints and cracks, press tightly to seal all gaps. To repair a larger crack, apply the Thiroco T-125 to cover the damaged surface then place a reinforcement membrane and then apply another coat of Thiroco T-125 over the entire patch. For easier application, store in a temperate place.
Use
It is mainly used to fill cracks, holes and repair deteriorated areas on foundations, asphalt roofs, shingle, vents and chimney joints. The Thiroco T-125 can be used on dry and wet surfaces.
Cleanning
Tools must be cleaned with mineral spirits.
Norm
CAN/O.N.G.C. 37.5M-89
Package
Available in 13.6 kg and 20kg.
Shelf Life
This product can be conserved in its original container, tightly sealed, up to 12 months after purchasing date by the applicator.
Technical Data Table
Specifications
ColorBlack
Solide90 - 99 %
Application to trowel or putty knifeApply coat of 3 mm (1/8") let dry before covering.
Application temperature-40°C to 80°C. The container can be stored in a temperate area for an easier application.
Coverage
4.5 m² (48.4 ft²) for a 13.6 kg
6.63 m² (71.4 ft²) for a 20 kg
The coverage rate is dependent of the surface porosity and temperature.
Density1,13 kg/L or 9,43 lbs/gal.
Touch dry±4 hours
Completely dry*±48 hours
Storage condition
Product must be conserved in a cool and well-ventilated place up 40°C. The product can withstand freezing.
* Drying Time depend of surface porosity and temperature.
Note
Close container after each uses. Keep out of reach of children. If product is applied near a ventilation or air conditioner unit, take necessary precautions to avoid infiltration of solvent odor inside. Keep any open container or freshly applied product away from open flames, sparks or others heat sources. For exterior uses only.
Warranty
10 years limited warranty when installed and / or applied as recommended by the manufacturer. We will replace the product with a manufacturing defect. Under any circumstances the manufacturer will be liable for any amount in excess of the purchase price of the product used. The consumer must ensure that this product is suitable for the intended use. Because of atmospheric conditions, applicator competence and surface conditions being independent of the manufacturer’s control, we limit our liability for one year following the date of purchase, with proof of purchase, to replacement of defective material only in its original hermetic container. Port paid factory (FAB factory).
DANGER
Flammable liquid and vapour. May be fatal if swallowed and enters airways. May cause cancer. Causes damage to organs through prolonged or repeated exposure.
Precautionary:
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not breathe dust/fumes/gas/mist/vapours/spray. Wash exposed and/or contaminated area thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective gloves/protective clothing/eye protection/face protection.
IF SWALLOWED: Do NOT induce vomiting. Immediately call a POISON CENTER or a doctor If exposed: Call a POISON CENTER or doctor/physician. Get medical advice/attention if you feel unwell. In case of fire: Use water fog, foam, dry chemical or carbon dioxide. Do not use straight of water. Store in a well ventilated place. Keep cool. Store locked up. Dispose of contents / container by a local waste disposal company according to regional regulations.
Condor 320 Rubberized Plastic Cement
Description
This excellent wet or dry surface rubberized plastic cement CR-320 contains elastomers and specially selected fibers for multipurpose applications. It is formulated to offer resistance against bad weather and flexibility as well as to be easy to apply. It becomes a strong, waterproof flexible coating once dried. Ideally suited for flat or metal roofs, but not recommended for asphalt shingles.
Surface Preparation
Surface must be structurally sound, clean and free of dust, dirt, rust, oil, grease, chipped paint, frost or any other contaminants.
Application
Can be applied with a towel, a caulking gun, a putty knife or by hand with gloves. To fill joints and cracks, push profoundly into gaps making bulge out on surface to avoid accumulation of water. Repair cracks, holes by applying a coat of 3 mm (1/8'') thick on defective sections and overtake of 150 mm (6'') around repairs. To ease application in cold season, keep product in a warm place.
Cleanning
Clean tools and equipment with mineral spirits.
Norm
CAN/O.N.G.C. 37.29-M89
Package
Available in tube of 300 ml and pails of 4 kg and 20 kg.
Shelf Life
This product can be conserved in its original container, tightly sealed, up to 12 months after purchasing date by the applicator.
Technical Data Table
Specifications
ColorBlack
Solids by Volume70 to 80 %
Weight1,05 kg/L (8,75 pounds/gal)
Coverage0,3 m²/kg (16 ft²/gal) coat of 3 mm (1/8'')
Tube : bead of 3 mm (1/8'') couvers ± 25 feet
Dry Time*
To 50 % R.H. 20° C (68° F)
To the Touch*1 hour
Completely Dry*24 hours
Service TemperatureMaximum : 85° C (185° F) dry coating
Application TemperatureAmbient (Thickens at low temperature)
Chemical Resistance
Resistant to water calcium chloride, salt and to lightly acid or alkaline solutions. Do not resist to oils, greases and solvents.
Permeance to Water Vapor (ASTM E96)3 mm (1/8'') coat before drying 2.9 ng/Pa.m2.s (0.05 perms)
* Drying Time depend of surface porosity and temperature.
Restriction
If product is applied near a ventillation unit or an air conditioner, take necessary precautions to avoid infiltration solvent odor inside. Protect freshly applied product and open container from open flame and adjacent welding activity. Do not apply all at once on vertical joints of more than 25 mm (1'') in width. Solvent contained in the product may stain wood and other absorbent materials. For EXTERIOR USE only.
Warranty
10 years limited warranty when installed and / or applied as recommended by the manufacturer. We will replace the product with a manufacturing defect. Under no circumstances will the manufacturer be liable for any amount in excess of the purchase price of the product used. The consumer must ensure that this product is suitable for the intended use. Because of atmospheric conditions, applicator competence and surface conditions being independent of the manufacturer's control, we limit our liability for one year following the date of purchase, with proof of purchase, to replacement of defective material only in its original hermetic container. Port paid factory (FAB factory).
DANGER
Flammable liquid and vapour. May be fatal if swallowed and enters airways. Causes serious eye irritation. May cause cancer. Suspected of damaging fertility or the unborn child. Causes damage to organs through prolonged or repeated exposure.
Precautionary:
Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. Do not breathe dust/fumes/gas/mist/vapours/spray. Wash exposed and/or contaminated area thoroughly after handling. Do not eat, drink or smoke when using this product. Wear protective gloves/protective clothing/eye protection/face protection.
IF SWALLOWED: Do NOT induce vomiting. Immediately call a POISON CENTER or a doctor IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do – continue rinsing. If exposed: Call a POISON CENTER or doctor/physician. Get medical advice/attention if you feel unwell. If eye irritation persists get medical advice/attention. In case of fire: Use water fog, foam, dry chemical or carbon dioxide. Do not use straight of water. Store in a well ventilated place. Keep cool. Store locked up. Dispose of contents / container by a local waste disposal company according to regional regulations.